ZB-U系列紡絲泵屬于齒輪形式的計量泵，是紡絲機上關健部件之一，其主共用途是將紡絲熔體均勻、等量地輸送到妨絲組件中，通過噴絲版微孔冷卻凝固成絲。
離壓熔融紡絲計量泵是由板件、齒輪、軸、傳動套、固定套、蓋板等零件組成。泵在運轉中被輸送被熔體進行自身潤滑。各種零件之間緊密配合，構成機械密封，可防止熔體滲出外漏。
泵的傳動是依靠紡絲機上專用傳動軸接頭與泵的傳動套配合而進行的。泵的放置方向?yàn)轫槙r(shí)針方向，不得反轉。計量泵出廠前，全部在專用的流量試驗機上檢驗合格。為了提高纖維的質量，在計量泵每次裝卸清洗之后，上紡絲機使用之前必須對泵進行流量測定并分組。
ZB-U series spinning pump is a metering pump in the form of gear, which is one of the key components of the spinning machine. The main purpose of the ZB-U series spinning pump is to distribute the spinning melt evenly and equally to the silk assembly. Microporous cooling solidification into a wire.
Structure and Characteristics of ZB - U Spinning Pump
Offset melt spinning metering pump is composed of plate parts, gears, shafts, transmission sets, fixed sets, cover plates and other parts. The pump is transported and is lubricated by the melt. A variety of parts in close cooperation, constitute a mechanical seal, to prevent leakage of the melt leakage.
The drive of the pump is carried out by cooperating with the drive jack on the spinning machine. The direction of the pump is clockwise and can not be reversed. Metering pump before leaving the factory, all in the special flow test machine inspection qualified. In order to improve the quality of the fiber, in the metering pump after each loading and unloading, the spinning machine must be used before the pump flow measurement and grouping.
紡滌綸、丙綸、錦綸長絲短絲、紡POY及FDY長絲。
Suit for Polypropylene, nylon filament short silk, spinning POY products and filament polyester FDY.
流量：0.1-150cc/rev
進出口：一進一出/二出、四出、六出、八出、一十六出。
材質：高溫工具鋼，合金鋼。
轉向：順時針
Flow: 0.1-150cc / rev
Inlet & Outlet: One inlet,one outlet /two outlets/four outlets/six outlets/eight outlets/sixteen outlets.
Material: high temperature tool steel, alloy steel.
Turn: clockwise
Flow:0.1-150cc / rev
出口壓力：≤50MPa
工作轉速：5-40rpm
大壓差：40mpa
工作溫度：≤350℃
清洗溫度：≤450℃
Outlet pressure: ≤ 50MPa
Working speed: 5-40rpm
Maximum pressure difference: 40mpa
Working temperature: ≤ 350 ℃
Cleaning temperature: ≤ 450 ℃
（本文來自http://www.belugapet.com，轉載請注明出處）
